Long rectangle resonator 1550 nm AlGaInAs/InP lasers

1550 nm AlGaInAs/InP long rectangle resonator lasers with three sides surrounded by SiO2 and p electrode layers are fabricated by planar technology, and room-temperature continuous-wave lasing is realized for a laser with a length of 53 mu m and a width of 2 mu m. Multiple peaks with wavelength intervals of Fabry-Perot mode intervals and mode Q factors of about 400 and a lasing mode with a Q factor over 8000 are observed from the lasing spectrum at threshold current. The numerical results of the FDTD simulation indicate that the lasing mode may be a whispering-gallery mode, which is a coupled mode of two high-order transverse modes of the waveguide.

对DES的Rectangle攻击和Boomerang攻击

作为加密标准，DES（data encryption standard）算法虽然已被AES（advanced encryption standard）算法所取代，但其仍有着不可忽视的重要作用．在一些领域，尤其是金融领域，DES和Triple DES仍被广泛使用着．而近年来又提出了一些新的密码分析方法，其中，Rectangle攻击和Boomerang攻击已被证明是非常强大而有效的．因此，有必要重新评估DES算法抵抗这些新分析方法的能力．研究了DES算法针对Rectangle攻击和Boomerang攻击的安全性．利用DES各轮最优差分路径及其概率，分别得到了对12轮DES的Rectangle攻击和对11轮DES的Boomerang攻击．攻击结果分别为：利用Rectangle攻击可以攻击到12轮DES，数据复杂度为2~(62)。个选择明文，时间复杂度为2~(42)次12轮加密；利用Boomerang攻击可以攻击到11轮DES，数据复杂度为2~(58)个适应性选择明密文，时间复杂度为2~(38)次11轮加密．由于使用的都是DES各轮的最优差分路径，所以可以相信，该结果是Rectangle攻击和Boomerang攻击对DES所能达到的最好结果．

Laser-induced wavy pattern formation in metal thin films

Laser-induced well-ordered and controllable wavy patterns are constructed in the deposited metal thin film. The micrometer-sized structure and orientation of the wavy patterns can be controlled via scanning a different size of rectangle laser spot on the films. Ordered patterns such as aligned, crossed, and whirled wave structures were designed over large areas. This patterning technique may find applications in both exploring the reliability and mechanical properties of thin films, and fabricating microfluidic devices. (C) 2004 American Institute of Physics.

Focusing properties of concentric piecewise cylindrical vector beam

The focusing properties of a concentric piecewise cylindrical vector beam is investigated theoretically in this paper. The beam consists of three portions with different and changeable phase retardation and polarization. Numerical simulations show that the evolution of the focal shape is very considerable by changing the radius and polarization rotation angle of each portion of the vector beam. And some interesting focal spots may occur, such as two- or three-peak focus, dark hollow focus, ring focus, and two-ring-peak focus. Corresponding gradient force patterns are also computed, and novel trap patterns, including cup shell shape trap with one trap at its each side along axis, rectangle shell shape trap with one trap at its each side, dumbbell optical trap, spherical shell optical trap, may occur, which shows that the concentric piecewise cylindrical vector beam can be used to construct controllable optical tweezers. (c) 2006 Elsevier GmbH. All rights reserved.

激光辐照引起Ge2Sb2Te5非晶态薄膜的电/光性质变化

研究了激光辐照引起Ge2Sb2Te5非晶态薄膜的电/光性质变化,当激光功率为580mW时薄膜的方块电阻有四个数量级（10^7～10^3Ω/□）的突变;对电阻发生突变前、中、后的三个样品进行了XRD测试,结果表明,随着激光功率的增大,薄膜由非晶态向晶态转变,用椭偏仪测试了结构转变前、中、后三个样品的光学常数,在可见光范围内薄膜的光学常数在波长相同情况下有：n（非晶态）〉n（中间态）〉n（晶态）,k（晶态）〉k（中间态）〉k（非晶态）,α（晶态）〉α（中间态）〉α（非晶态）,结合电阻变化曲线和XRD图谱讨论了激光辐照Ge2Sb2Te5非晶态薄膜的电/光性质变化同激光功率和结构转变之间的关系.

Mode analysis and Q-factor enhancement due to mode coupling in rectangular resonators

Modes in rectangular resonators are analyzed and classified according to symmetry properties, and quality factor (Q-factor) enhancement due to mode coupling is observed. In the analysis, mode numbers p and q are used to denote the number of wave nodes in the direction of two orthogonal sides. The even and odd mode numbers correspond to symmetric and antisymmetric field distribution relative to the midlines of sides, respectively. Thus, the modes in a rectangle resonator can be divided into four classes according to the parity of p and q. Mode coupling between modes of different classes is forbidden; however, anti-crossing mode coupling between the modes in the same class exists and results in new modes due to the combination of the coupled modes. One of the combined modes has very low power loss and high Q-factor based on far-field emission of the analytical field distribution, which agrees well with the numerical results of the finite-difference time-domain (FDTD) simulation. Both the analytical and FDTD results show that the Q-factors of the high Q-factor combined modes are over one order larger than those of the original modes. Furthermore, the general condition required to achieve high-Q modes in the rectangular resonator is given based on the analytical solution.

分组密码的分析与设计

分组密码作为现代密码学的一个重要组成部分，是目前最重要和流行的一种数据加密技术，有着非常广泛的应用。此外，近年来分组密码或其组件还经常作为基础模块用于构造Hash函数，MAC算法等。因此对分组密码安全性的分析以及设计安全高效的分组密码算法，在理论研究及实际应用中都有着非常重要的意义。本文的研究内容主要包括两个方面：对现有常用分组密码的安全性分析，以及分组密码及其组件的设计。这两个方面是密不可分，相互融合的。通常都是利用算法存在的弱点或算法设计特点，提出新的密码分析算法。而在算法设计过程中，正是从密码分析获取经验，掌握设计算法的技巧和避免可能存在的缺陷。 本文首先对分组密码分析方法作了大量的调查和研究，在此基础上分析了一些国内外常用和有影响的分组密码，得到了一系列有价值的分析结果。并在密码分析工作的经验基础上，结合现有密码设计理论，在分组密码及其组件的设计方面做了比较深入的研究。本文的主要成果包括： (1) DES算法的分析。DES算法是迄今最重要的分组密码算法之一，目前在一些金融领域，DES和Triple-DES仍被广泛使用着。本文考察了DES算法针对Boomerang攻击和Rectangle攻击的安全性。通过利用DES算法各轮的最优差分路径及其概率，分别给出了这两种攻击方法对DES的攻击算法。 (2) Rijndael算法的分析。Rijndael算法是高级加密标准AES的原型。本文针对大分组Rijndael算法的各个不同版本，利用算法行移位和列混淆变换的一些密码特性，改进了原有的不可能差分攻击结果，极大的降低了攻击的数据和时间复杂度。同时还分别构造了一些新的更长轮的不可能差分路径，利用这些路径给出了一系列对大分组Rijndael算法的改进的不可能差分攻击，这些结果是目前已知的对该算法的最好攻击结果。 (3) SMS4算法的分析。SMS4算法是中国公布的用于无线局域网产品保护的算法。本文首先构造了SMS4算法的一类5轮循环差分特征，利用该特征分别给出了对16轮SMS4算法的矩阵攻击和对21轮SMS4算法的差分分析。随后考察了SMS4算法抵抗差分故障攻击的能力，基于字节故障模型，结合实验指出需要32次故障诱导来恢复全部密钥。后续的工作又进一步将结果改进为只需要进行一次故障诱导再结合2^{44}次密钥搜索即可恢复全部密钥。 (4) CLEFIA密码算法的分析。CLEFIA算法是索尼公司于2007年提出的用于产品版权保护和认证的分组密码算法。针对CLEFIA算法，本文构造了一条概率为1的5轮截断差分特征，再结合其扩散矩阵的密码特性构造了一条3轮线性逼近。随后利用这两条路径组成的8轮差分-线性区分器，给出了对10轮CLEFIA算法的有效的差分-线性攻击。 (5) 分组密码结构的设计及其应用。本文提出了两种新的分组密码结构，并指出了其与原有结构相比的优势，同时分别评估了这两种结构针对差分分析和线性分析等常用密码分析方法的安全性。基于这两个密码结构，结合部分密码组件的设计和测试工作，本文还完成了两个分组密码算法的概要设计，并简要评估了它们的实现效率及针对现有的几种主要密码分析方法的安全性。

迷宫流道转角对灌水器水力性能的影响

为研究齿形、梯形以及矩形流道转角变化对水力性能的影响,采用Fluent软件对不同形状下不同转角的流道进行了数值模拟。研究结果表明:当其他条件相同时,转角的变化与流量系数、流态指数呈负相关,其变化对梯形流道灌水器的流量系数影响最大,最多下降了19.03%,齿形流道次之,下降了10.14%,矩形流道是梯形流道转角角度增加的延伸,具有相同的水力性能变化规律;随着角度的增加,梯形流道总的局部水头损失系数最多增加了32.5%,而齿形流道总的局部水头损失系数最多增加了23.4%,变化都很明显;压力较高时,摩阻系数基本保持不变,流体为紊流状态。

The effect of human rhythm on packet delivery

In communication networks such as the Internet, the relationship between packet generation rate and time is similar to a rectangle wavefunction due to the rhythm of humans. Thus, we investigate the traffic dynamics on a network with a rectangle wavepacket generation rate. It is found that the critical delivering capacity parameter beta(c) (which separates the congested phase and the free phase) decreases significantly with the duty cycle r of the rectangle wave for package generation. And, in the congested phase, more collective generation of packets (smaller r) is helpful for decreasing the packet aggregation rate. Moreover, it is found that the congested phase can be divided into two regions, i.e., region1 and region2, where the distributions of queue lengths are nonlinear and linear, respectively. Also, the linear expression for the distribution of queue lengths in region2 is obtained analytically. Our work reveals an obvious effect of the rectangle wave on the traffic dynamics and the queue length distribution in the system, which is of essential interest and may provide insights into the designing of work-rest schedules and routing strategies.

八单元一维位置灵敏雪崩室

In the experiment of nuclear reaction, it is important to measure the mass, charge, energy and emitted direction of particles. For multiparameter measurement, we must use a detector or a group of detectors which can give the time, energy, and position information. The Large Area position sensitive Ionization Chamber(LAIC) is one of the eight experiment terminals of HIRFL. It is built for researching nuclear reactions from low energy to intermediate energy. It is an excellent equipment for energy measurements and atomic number identification of emitted fragments in this energy region. It is also designed to give the time and position information of the emitted fragments by itself. Obviously, an IC can not supply a good timing signal. Moreover, the mechanical installation is different from the original design by some other reasons. In this case, it is not enough to obtain the correct direction information of the emitted fragments. To obtain good timing signals and the correct direction information, some modifications must be made. It is well known that a PPAC can give us excellent timing signals. It also can be easily built as a position sensitive detector. For this reason, a specially designed PPAC is installed in the entrance of the LAIC. For the different purposes, two types of PPACs were designed and tested. Both are OCTPSACs (OCTunit one dimension Position Sensitive Avalanche Counter). In this paper, both OCTPSACs will be introduced. Based on the requirements of the LAIC, the OCTPSACs consist of eight position sensitive PPACs. Each PPAC has an anode and a cathode. In both cases, the sizes are same. But different type of cathodes are used. In one type of OCTPSAC, its cathode is made of wire plane. It consists of gold-plated tungsten wires with the diameter of 20μm, spaced 0.5 mm apart from each other. The anode is a mylar foil which was evaporated by gold layer with the thickness of 50μg/cm~2 mounted on a printed plate in the shape of rectangle. the thickness of mylar foil is 1.5μm. The gap between anode and cathode is 3mm. The performance of the OCTPSAC has been tested by using a ~(252)Cf source in flowing isobutylene gas at the pressure of 3.4mb. The intrinsic time resolution of 289ps and position resolution of 2 mm have been obtained. In another type of OCTPSAC, the cathode is made of mylar foil, which is composed of gold strip by vacuume evaporation method with a special mask on the mylar foil. The thickness and the width of the gold strip is 50μg/cm~2 and 1.7mm. The strips are spaced 0.3 mm apart from each other. The anode is the same as the former type. We have obtained the time resolution of 296ps and position resolution of 2mm by using ~(241)Am-a source when the gas pressure is 6 mb and high voltage is 600V. The working gas is heptane

Phase transition of BaNd2Mn2O7

Phase transition of BaNd2Mn2O7 from orthorhombic (space group Fmmm) to tetragonal phase (I4/mmm) was studied by high temperature powder X-ray diffractometry and Rietveld analysis. The transition temperature was identified at 523 K, which is almost the same transition temperature as the compounds with other rare earth ions in this BaLn(2)Mn(2)O(7) family (Ln=Sm and Eu) with Fmmm space group. During the transition an oxygen octahedron of each phase changes a little its form, in which four oxygen atoms perpendicular to C-axis make a rectangle and a square for orthorhombic and tetragonal phases, respectively. Manganese ion is not on the center of the quadrilateral consisting of these four oxygen ions, but a little apart from the center along c-axis in both phases.

Trichodinid ectoparasites (Ciliophora, Peritrichia) from the tiger puffer Takifugu rubripes in the Yellow Sea, with revision of Trichodina jadranica Raabe,1958

Two ectoparasitic ciliates, Trichodina fugu Imai et al., 1997 and T. jadranica Raabe, 1958, found on the gills and skin of the maricultured tiger puffer Takifugu rubripes on the China coast of the Yellow Sea, were studied using the dry silver nitrate method. Trichodina fugu is distinguished by its almost rod-shaped denticle blades. Trichodina jadranica is usually described as a small trichodinid with a clear central circle in the adhesive disc and with a low number of denticles. However, the data available suggest that the species is highly variable in morphometry and the Chinese population represents the largest in body size and denticle dimensions found to date. Based on the revision of T. jadranica, two major morphotypes, each represented by several populations are classified, differing in the shape of the blades, viz., distinctly curved and sickle-shaped with pointed distal ends (as in the classical T. jadranica) vs. less curved and more or less rectangle-like with rounded distal ends (as in T. domerguei gobii). Trichodina domerguei gobii Raabe,.1959, which was synonymised with T. jadranica, is thus elevated to species rank. Furthermore, Trichodina jadranica noblei Lom, 1970 has straight and stout blades with broadly rounded distal ends and is raised to species rank: T noblei Lom, 1970. Trichodina jadranica sensu Xu et al., 1995 shows high similarities in denticle shape and dimensions as well as the central granule pattern with T chlamydis Xu et al., 1999. Thus, it is synonymised with the latter species.

基于水下作业系统阻抗力控制水下目标定位

提出了基于水下作业系统阻抗力控制的水下矩形围壁定位方法。水下作业系统末端执行器跟踪期望运动轨迹,通过与水下矩形围壁环境表面接触力反馈信息的变化获得与环境接触的特殊点,计算得到矩形围壁环境相对水下作业系统的位姿。以带有三自由度机械手的水下作业系统为例进行水下矩形围壁目标表面恒力跟踪的计算机仿真,仿真结果表明定位方法可以很好的获得矩形围壁环境的位姿,控制策略具有很好的表面跟踪和力控制能力。

各向同性与各向异性介质中地震波旅行时正演模拟与反演成像

By seismic tomography, interesting results have been achieved not only in the research of the geosphere with a large scale but also in the exploration of resources and projects with a small scale since 80'. Compared with traditional inversion methods, seismic tomography can offer more and detailed information about subsurface and has been being paid attention by more and more geophysicists. Since inversion based on forward modeling, we have studied and improved the methods to calculate seismic traveltimes and raypaths in isotropic and anisotropic media, and applied the improved forward methods to traveltime tomography. There are three main kinds of methods to calculate seismic traveltime field and its ray path distribution, which are ray-tracing theory, eikonal equation by the finite-difference and minimum traveltime tree algorithm. In ray tracing, five methods are introduced in the paper, including analytic ray tracing, ray shooting, ray bending, grid ray tracing and rectangle grid ray perturbation with three points. Finite-difference solution of eikonal equation is very efficient in calculation of seismic first-break, but is awkward in calculation of reflection traveltimes. We have put forward a idea to calculate traveltimes of reflected waves using a combining way of eikonal equation method and other one in order to improve its capability of dealing with reflection waves. The minimum traveltime tree algorithm has been studied with emphases. Three improved algorithms are put forward on the basis of basic algorithm of the minimum traveltime tree. The first improved algorithm is called raypath tracing backward minimum traveltime algorithm, in which not only wavelets from the current source but also wavelets from upper source points are all calculated. The algorithm can obviously improve the speed of calculating traveltimes and raypaths in layered or blocked homogeneous media and keep good accuracy. The second improved algorithm is raypath key point minimum traveltime algorithm in which traveltimes and raypaths are calculated with a view of key points of raypaths (key points of raypths mean the pivotal points which determine raypaths). The raypath key point method is developed on the basis of the first improved algorithm, and has better applicability. For example, it is very efficient even for inhomogeneous media. Another improved algorithm, double grid minimum traveltime tree algorithm, bases upon raypath key point scheme, in which a model is divided with two kinds of grids so that the unnecessary calculation can be left out. Violent undulation of curved interface often results in the phenomenon that there are no reflection points on some parts of interfaces where there should be. One efficacious scheme that curved interfaces are divided into segments, and these segments are treated respectively is presented to solve the problem. In addition, the approximation to interfaces with discrete grids leads to large errors in calculation of traveltimes and raypaths. Noting the point, we have thought a new method to remove the negative effect of mesh and to improve calculation accuracy by correcting the traveltimes with a little of additional calculation, and obtained better results.